This chapter describes Layer Two Tunneling (L2) messages. For information on message content and how to use the message, refer to the Introduction.
| L2.001 |
Level: UI_ERROR
Short Syntax: L2.001 ERROR: errorString
Long Syntax: L2.001 ERROR: errorString
Description: General Error - If this happens, something is seriously wrong. A brief description of what happened and/or where it happened will accompany this message.
| L2.002 |
Level: CI_ERROR
Short Syntax: L2.002 WARNING: warningString
Long Syntax: L2.002 WARNING: warningString
Description: General Warning - This can happen in normal conditions when resources are depleted (buffers, nets, calls, tunnels, etc.) or when our peer does something unexpected. A brief description of what happened and/or where it happened will accompany this message.
| L2.003 |
Level: C-INFO
Short Syntax: L2.003 L2 Slf Tst net net
Long Syntax: L2.003 Performing Self Test on L2 network net
Description: Entering l2tp_slftst
| L2.004 |
Level: C-INFO
Short Syntax: L2.004 L2 init net net
Long Syntax: L2.004 Intitalizing L2 network net
Description: Entering l2tp_init
| L2.005 |
Level: C-INFO
Short Syntax: L2.005 L2 install net net
Long Syntax: L2.005 Installing L2 network net
Description: Entering l2tp_install
| L2.006 |
Level: C-INFO
Short Syntax: L2.006 LCP start net net cause= cause
Long Syntax: L2.006 Renegotiate LCP-L2 net net, cause= cause
Description: LCP restarted on the L2 network due to the listed cause.
| L2.007 |
Level: C-INFO
Short Syntax: L2.007 LNS action L2 net net
Long Syntax: L2.007 LNS action L2 network net
Description: Allocated/Freed (action) an L2 Network on the LNS
| L2.008 |
Level: P_TRACE
Short Syntax: L2.008 Call Make AVPtype AVP,attr= attributeNo,val= value,len= length,flag= flags
Long Syntax: L2.008 Call Make AVPtype AVP,attr= attributeNo,val= value,len= length,flag= flags
Description: Call is creating an AVP with the attributes given. A value of 0 can indicate that the value is very long and could not be displayed in the message.
| L2.009 |
Level: P_TRACE
Short Syntax: L2.009 Call Rcv AVPtype AVP,attr= attributeNo,val= value,len= length,flag= flags
Long Syntax: L2.009 Call Rcv AVPtype AVP,attr= attributeNo,value= value,len= length,flags= flags
Description: Call is receiving an AVP with the attributes given. A value of 0 can indicate that the value is very long and could not be displayed in the message, or is not supported locally.
| L2.010 |
Level: C_TRACE
Short Syntax: L2.010 Start Call LAC net net,speed= speed,btype= bearer,frame= framing,auth= proxy_auth
Long Syntax: L2.010 Start Call LAC net net,speed= speed,btype= bearer,ftype= framing,auth= proxy_auth
Description: Starting Call FSM from LAC. Listed parameters are speed (bits/sec), bearer type, framing type, and proxy-auth-type.
| L2.011 |
Level: C_TRACE
Short Syntax: L2.011 Stopping Call id= callid, net net int /
Long Syntax: L2.011 Stopping Call id= callid, net net int /
Description: Stopping a call
| L2.012 |
Level: C-INFO
Short Syntax: L2.012 Local Term net net
Long Syntax: L2.012 Local Terminate L2 network net
Description: Local Terminate means graceful teardown or a physical down event for any reason.
| L2.013 |
Level: C-INFO
Short Syntax: L2.013 type Call id State Changed old -> new
Long Syntax: L2.013 type Call id State Changed old -> new
Description: Call state changed.
| L2.014 |
Level: C_TRACE
Short Syntax: L2.014 CallORTunnel from net net
Long Syntax: L2.014 CallORTunnel from net net
Description: This is the Entry into the L2 system. Starting a call (and possibly needing to start a tunnel).
| L2.015 |
Level: C_TRACE
Short Syntax: L2.015 Call Established- Type,net= net,speed= speed,flags= sendFlags
Long Syntax: L2.015 Call Established- Type,net= net,speed= speed,flags= sendFlags
Description: Call FSM reached the established state.
| L2.016 |
Level: C_TRACE
Short Syntax: L2.016 Forcing intial CHAP challenge
Long Syntax: L2.016 Forcing intial CHAP challenge
Description: The peer has sent Proxy-CHAP, but the user has configured to force an initial CHAP re-challenge for security reasons.
| L2.017 |
Level: C_TRACE
Short Syntax: L2.017 Using Proxy- authType AUTH on net net
Long Syntax: L2.017 Using Proxy- authType AUTH on net net
Description: LNS is accepting the proxy-auth type indicated from the peer.
| L2.018 |
Level: C_TRACE
Short Syntax: L2.018 Aborting Call, callid= callid, net= net
Long Syntax: L2.018 Aborting Call, callid= callid, net= net
Description: Aborting Call
| L2.019 |
Level: C_TRACE
Short Syntax: L2.019 Cleaning up type Call id= callid
Long Syntax: L2.019 Cleaning up type Call id= callid
Description: Cleaning up call structure and state
| L2.020 |
Level: P_TRACE
Short Syntax: L2.020 RCV type, callid= callid, net= net
Long Syntax: L2.020 RCV type, callid= callid, net= net
Description: Receive the indicated call control message. Net is 0 for a resource condition.
| L2.021 |
Level: P_TRACE
Short Syntax: L2.021 SEND type, callid= callid, net= net
Long Syntax: L2.021 SEND type, callid= callid, net= net
Description: Send the indicated call control message. Net is 0 for a resource condition.
| L2.022 |
Level: P_TRACE
Short Syntax: L2.022 protocol PAYLOAD RCVD bytes bytes, net net, callid= cid
Long Syntax: L2.022 protocol PAYLOAD RCVD bytes bytes, net net, callid= cid
Description: Received a PAYLOAD packet on LAC/LNS or PAC/PNS
| L2.023 |
Level: P_TRACE
Short Syntax: L2.023 Send type Zero Len Body (ZLB), tid= tid,cid= cid
Long Syntax: L2.023 Send type Zero Len Body (ZLB), tid= tid,cid= cid
Description: About to send a ZLB to the peer to ACK.
| L2.024 |
Level: P_TRACE
Short Syntax: L2.024 protocol PAYLOAD SEND bytse bytes, net= net, callid= cid
Long Syntax: L2.024 protocol PAYLOAD SEND bytse bytes, net= net, callid= cid
Description: Send L2TP/PPTP Payload
| L2.025 |
Level: P_TRACE
Short Syntax: L2.025 LNS Rcvd Proxy-Lcp type updating local_remote
Long Syntax: L2.025 LNS Rcvd Proxy-Lcp type updating local_remote
Description: LNS received proxy-lcp from LAC
| L2.026 |
Level: P_TRACE
Short Syntax: L2.026 LNS Forcing LCP MRU= mru
Long Syntax: L2.026 LNS Forcing LCP MRU= mru
Description: LNS processing proxy-mru from LAC
| L2.027 |
Level: P_TRACE
Short Syntax: L2.027 LNS Forcing LCP ACCM= accm
Long Syntax: L2.027 LNS Forcing LCP ACCM= accm
Description: LNS processing proxy-accm from LAC
| L2.028 |
Level: P_TRACE
Short Syntax: L2.028 LNS Forcing LCP Auth= auth_type
Long Syntax: L2.028 LNS Forcing LCP Auth= auth_type
Description: LNS processing proxy-lcp auth from LAC
| L2.029 |
Level: P_TRACE
Short Syntax: L2.029 LNS Forcing LCP Magic Number= auth_type
Long Syntax: L2.029 LNS Forcing LCP Magic Number= auth_type
Description: LNS processing proxy-magic-number from LAC
| L2.030 |
Level: P_TRACE
Short Syntax: L2.030 LNS Forcing LCP option option
Long Syntax: L2.030 LNS Forcing LCP option option
Description: LNS processing proxy-lcp option from LAC
| L2.031 |
Level: P_TRACE
Short Syntax: L2.031 LNS Forcing LCP Quality prot= prot, period= period
Long Syntax: L2.031 LNS Forcing LCP Quality prot= prot, period= period
Description: LNS processing proxy-lcp quality from LAC
| L2.032 |
Level: P_TRACE
Short Syntax: L2.032 LNS Forcing LCP MRRU= MRRU
Long Syntax: L2.032 LNS Forcing LCP MRRU= MRRU
Description: LNS processing proxy-mrru from LAC
| L2.033 |
Level: P_TRACE
Short Syntax: L2.033 LNS Forcing LCP Endpt Disc cls= class, addr= address
Long Syntax: L2.033 LNS Forcing LCP Endpt Disc cls= class, addr= address
Description: LNS processing proxy-endpt-discriminator from LAC
| L2.034 |
Level: P_TRACE
Short Syntax: L2.034 LNS Forcing LCP Link-Discriminator= ld
Long Syntax: L2.034 LNS Forcing LCP Link-Discriminator= ld
Description: LNS processing proxy-link-discriminator from LAC
| L2.035 |
Level: P_TRACE
Short Syntax: L2.035 Tunnel Auth Create type, Tid= tid/ len, Len=
Long Syntax: L2.035 Tunnel Auth Create type, Tid= tid/ len, Len=
Description: Creating Tunnel Auth AVPs
| L2.036 |
Level: P_TRACE
Short Syntax: L2.036 Create Result Code AVP:rslt= result,err= error
Long Syntax: L2.036 Create Result Code AVP:rslt= result,err= error
Description: Creating result code AVP
| L2.037 |
Level: C_INFO
Short Syntax: L2.037 l2tp_conf init L2-tunneling maxcalls= maxcalls maxtunnels= maxtunnels
Long Syntax: L2.037 l2tp_conf init L2-tunneling maxcalls= maxcalls maxtunnels= maxtunnels
Description: performing layer-2-tunneling intialization
| L2.038 |
Level: CE_ERROR
Short Syntax: L2.038 PPP Discard packet - setting up tunnel, net net
Long Syntax: L2.038 PPP Discard packet - setting up tunnel, net net
Description: discarding PPP packet from client because the tunnel/call has not been established.
| L2.039 |
Level: C_INFO
Short Syntax: L2.039 NOTE: note_msg
Long Syntax: L2.039 NOTE: note_msg
Description: General Note
| L2.040 |
Level: P_TRACE
Short Syntax: L2.040 RCV protocol:F= flags,L= length,Tid= tunnelid,Cid= callid,NS= ns,NR= nr,O= offset
Long Syntax: L2.040 RCV protocol:F= flags,L= length,Tid= tunnelid,Cid= callid,NS= ns,NR= nr,O= offset
Description: Layer-2-Tunneling component received a tunneled packet. It is important to note that some of the displayed fields may NOT have been rcvd - use the "flags" mask to find which ones were rcvd.
| L2.041 |
Level: P_TRACE
Short Syntax: L2.041 SND protocol:F= flags,L= length,Tid= tunnelid,Cid= callid,NS= ns,NR= nr,O= offset
Long Syntax: L2.041 SND protocol:F= flags,L= length,Tid= tunnelid,Cid= callid,NS= ns,NR= nr,O= offset
Description: Layer-2-Tunneling component sending a tunneled packet. It is important to note that some of the displayed fields may NOT have been sent - use the "flags" mask to find which ones were sent.
| L2.042 |
Level: P_TRACE
Short Syntax: L2.042 Rcvd pkt udp_len= WUDP_LEN, L2_len= L2_LEN
Long Syntax: L2.042 Rcvd pkt udp_len= WUDP_LEN, L2_len= L2_LEN
Description: UDP pkt length does not match L2 packet length
| L2.043 |
Level: P_TRACE
Short Syntax: L2.043 RCV type Zero Len Body (ZLB), tid= tid,cid= cid
Long Syntax: L2.043 RCV type Zero Len Body (ZLB), tid= tid,cid= cid
Description: Received a ZLB from our peer
| L2.044 |
Level: C_INFO
Short Syntax: L2.044 Allocating UDP port port for tunnelid= tid
Long Syntax: L2.044 Allocating UDP port port for tunnelid= tid
Description: allocated a UDP source port for tunnel
| L2.045 |
Level: P_TRACE
Short Syntax: L2.045 packet Pkt Queued for delayed type XMT, id= id
Long Syntax: L2.045 packet Pkt Queued for delayed type XMT, id= id
Description: The Layer-2-Tunneling system is busy (xmt window is full), this packet was queued for delayed transmit.
| L2.046 |
Level: C_INFO
Short Syntax: L2.046 Clearing callid= callid, tunnelid= tunnelid
Long Syntax: L2.046 Clearing callid= callid, tunnelid= tunnelid
Description: clearing call
| L2.047 |
Level: C-INFO
Short Syntax: L2.047 Tunnel tid/ peer-tid State Changed old -> new
Long Syntax: L2.047 Tunnel tid/ peer-tid State Changed old -> new
Description: Call state changed.
| L2.048 |
Level: P_TRACE
Short Syntax: L2.048 RCV type, tid= tid/ peer-tid
Long Syntax: L2.048 RCV type, tid= tid/ peer-tid
Description: Receive the indicated tunnel control message.
| L2.049 |
Level: P_TRACE
Short Syntax: L2.049 SEND type, tid= tid/ peer-tid
Long Syntax: L2.049 SEND type, tid= tid/ peer-tid
Description: Send the indicated tunnel control message.
| L2.050 |
Level: C_INFO
Short Syntax: L2.050 EVENT event,tid= tunnelid/ peerid,state= state
Long Syntax: L2.050 EVENT event,tid= tunnelid/ peerid,state= state
Description: Tunnel Originator/Receiver Event
| L2.051 |
Level: C_INFO
Short Syntax: L2.051 Cleaning up tunnelid tid/ peerid
Long Syntax: L2.051 Cleaning up tunnelid tid/ peerid
Description: cleaning up tunnel
| L2.052 |
Level: C_INFO
Short Syntax: L2.052 Tunnel tid/ peer-tid has seconds seconds to establish itself
Long Syntax: L2.052 Tunnel tid/ peer-tid has seconds seconds to establish itself
Description: Bring down the tunnel if it is not established in <seconds> seconds.
| L2.053 |
Level: C_INFO
Short Syntax: L2.053 tid tid/ peerid will shutdown in seconds seconds
Long Syntax: L2.053 tid tid/ peerid will shutdown in seconds seconds
Description: Tunnel will shutdown in <seconds> seconds.
| L2.054 |
Level: C_INFO
Short Syntax: L2.054 Assigning tunnel peer peer, tid= IP/ address
Long Syntax: L2.054 Assigning tunnel peer peer, tid= IP/ address
Description: Assigning tunnel
| L2.055 |
Level: C_INFO
Short Syntax: L2.055 Delayed Tunnel clean-up tid= tid/ peer-tid, already doomed
Long Syntax: L2.055 Delayed Tunnel clean-up tid= tid/ peer-tid already doomed
Description: Delayed tunnel clean-up
| L2.056 |
Level: C_INFO
Short Syntax: L2.056 Call to kill tunnel tid/ now, already doomed, die gracefully
Long Syntax: L2.056 Call to kill tunnel tid/ now, already doomed, die gracefully
Description: Kill tunnel
| L2.057 |
Level: P_TRACE
Short Syntax: L2.057 Processing Challenge Response from Peer peer
Long Syntax: L2.057 Processing Challenge Response from Peer peer
Description: process challenge response
| L2.058 |
Level: P_TRACE
Short Syntax: L2.058 Peer Attribute = value
Long Syntax: L2.058 Peer Attribute = value
Description: process Tunnel AVP (value is integer)
| L2.059 |
Level: P_TRACE
Short Syntax: L2.059 Peer Attribute = value
Long Syntax: L2.059 Peer Attribute = value
Description: process Tunnel AVP (value is hex)
| L2.060 |
Level: P_TRACE
Short Syntax: L2.060 Peer Attribute = value
Long Syntax: L2.060 Peer Attribute = value
Description: process Tunnel AVP (value is string)
| L2.061 |
Level: C_INFO
Short Syntax: L2.061 unsuccessful result: code= result,error= error msg=
Long Syntax: L2.061 unsuccessful result: code= result,error= error msg=
Description: Result of processing Start Control Connection Request/Reply/Connected.
| L2.062 |
Level: C_INFO
Short Syntax: L2.062 action all calls on tunnel tid
Long Syntax: L2.062 action all calls on tunnel tid
Description: killing/clearing all calls on tunnel.
| L2.063 |
Level: P_TRACE
Short Syntax: L2.063 Retransmit msgtype on tunnel tid call cid
Long Syntax: L2.063 Retransmit msgtype on tunnel tid call cid
Description: Retransmitting packet after timeout waiting for ACK.
| L2.064 |
Level: CE_ERROR
Short Syntax: L2.064 Timeout waiting for ACK call cid
Long Syntax: L2.064 Timeout waiting for ACK call cid
Description: ACK timeout
| L2.065 |
Level: CE_ERROR
Short Syntax: L2.065 Declaring LOST pkt on call cid
Long Syntax: L2.065 Declaring LOST pkt on call cid
Description: declare lost packet
| L2.066 |
Level: CE_ERROR
Short Syntax: L2.066 Tunnel Retransmit limit exceeded - killing tunnel tid
Long Syntax: L2.066 Tunnel Retransmit limit exceeded - killing tunnel tid
Description: Tunnel retransmit maximum
| L2.067 |
Level: C_INFO
Short Syntax: L2.067 Result Code Rx code= result_code error= error_code msg= message
Long Syntax: L2.067 Result Code Rx code= result_code error= error_code msg= message
Description: Result Code recevied
| L2.068 |
Level: C_INFO
Short Syntax: L2.068 L2TPSEC: Processing Encoded Key AVP a b c d e f g h i j k l m n o p
Long Syntax: L2.068 L2TPSEC: Processing Encoded Key AVP a b c d e f g h i j k l m n o p
Description: l2tpsec encoded key avp
| L2.069 |
Level: C_INFO
Short Syntax: L2.069 L2TPSEC: Decoded Key: a b c d e f g h i j k l m n o p
Long Syntax: L2.069 L2TPSEC: Decoded Key: a b c d e f g h i j k l m n o p
Description: l2tpsec encoded key avp
| L2.070 |
Level: C_INFO
Short Syntax: L2.070 L2TPSEC: Create Encoded Key AVP a b c d e f g h i j k l m n o p
Long Syntax: L2.070 L2TPSEC: Create Encoded Key AVP a b c d e f g h i j k l m n o p
Description: l2tpsec encoded key avp
| L2.071 |
Level: C_INFO
Short Syntax: L2.071 L2TPSEC: Actual Key is: a b c d e f g h i j k l m n o p
Long Syntax: L2.071 L2TPSEC: Actual Key is: a b c d e f g h i j k l m n o p
Description: l2tpsec encoded key avp
| L2.072 |
Level: C_INFO
Short Syntax: L2.072 RESET: R Bit rcvd - clear ns= ns thru mynr= nr
Long Syntax: L2.072 RESET: R Bit rcvd - clear ns= ns thru mynr= nr
Description: R bit received from peer
| L2.073 |
Level: C_INFO
Short Syntax: L2.073 type Originate Tunnel to peer peer
Long Syntax: L2.073 type Originate Tunnel to peer peer
Description: Originating Tunnel Session
| L2.074 |
Level: C_INFO
Short Syntax: L2.074 Upcall from AAA subsystem, request status
Long Syntax: L2.074 Upcall from AAA subsystem, request status
Description: Output the result from the upcall from AAA (RADIUS/local-list)
| L2.075 |
Level: C_INFO
Short Syntax: L2.075 Idle Timer Expired - Net net
Long Syntax: L2.075 Idle Timer Expired - Net net
Description: Demand circuit going down due to idle timeout
| L2.076 |
Level: C_INFO
Short Syntax: L2.076 Fixed Outbound L2 circuit - intiate call Nt net
Long Syntax: L2.076 Fixed Outbound L2 circuit - intiate call Nt net
Description: fixed circuit running self-test - initiate call
| L2.077 |
Level: C_INFO
Short Syntax: L2.077 Demand Outbound L2 circuit - n_up Nt net
Long Syntax: L2.077 Demand Outbound L2 circuit - n_up Nt net
Description: Demand circuit running self-test - bring protocols up
| L2.078 |
Level: C_INFO
Short Syntax: L2.078 protocol callid/ peer_callid EVENT event,state= state
Long Syntax: L2.078 protocol callid/ peer_callid EVENT event,state= state
Description: PPTP/L2F session event
| L2.079 |
Level: C-INFO
Short Syntax: L2.079 AVAILABLE
Long Syntax: L2.079 AVAILABLE
Description: AVAILABLE
| L2.080 |
Level: P-TRACE
Short Syntax: L2.080 PPTP Send messageType, tid= tunnelid,cid= callid
Long Syntax: L2.080 PPTP Send messageType, tid= tunnelid,cid= callid
Description: PPTP Sends a Call Control Message
| L2.081 |
Level: P-TRACE
Short Syntax: L2.081 PPTP Rcv messageType, tid= tunnelid,cid= callid
Long Syntax: L2.081 PPTP Rcv messageType, tid= tunnelid,cid= callid
Description: PPTP Receives a Call Control Message
| L2.082 |
Level: P-TRACE
Short Syntax: L2.082 ICRQ: serial num= sn, bearer
Long Syntax: L2.082 ICRQ: serial num= sn, bearer
Description: PPTP Receives Incoming Call Request with values for call serial number ...
| L2.083 |
Level: C-INFO
Short Syntax: L2.083 PPTP Tunnel id State Changed -> newstate
Long Syntax: L2.083 PPTP Tunnel id State Changed -> newstate
Description: PPTP Tunnel state changed.
| L2.084 |
Level: C-INFO
Short Syntax: L2.084 PPTP Tunnel id/ peer_id EVENT event,state= state
Long Syntax: L2.084 PPTP Tunnel id/ peer_id EVENT event,state= state
Description: PPTP tunnel event
| L2.085 |
Level: P-TRACE
Short Syntax: L2.085 Rcv PPTP Start-Control-Conn-Req from host remote_hostname
Long Syntax: L2.085 Rcv PPTP Start-Control-Conn-Req from host remote_hostname
Description: Received PPTP Start control connection request from peer
| L2.086 |
Level: P-TRACE
Short Syntax: L2.086 Rcv PPTP Stop-Control-Conn-Req reason reason
Long Syntax: L2.086 Rcv PPTP Stop-Control-Conn-Req reason reason
Description: Received PPTP Stop control connection request from peer
| L2.087 |
Level: P-TRACE
Short Syntax: L2.087 Rcv PPTP Echo-Req id id
Long Syntax: L2.087 Rcv PPTP Echo-Req id id
Description: Received PPTP Echo request
| L2.088 |
Level: C_INFO
Short Syntax: L2.088 Generr in Function: errorcode
Long Syntax: L2.088 General error in Function with error code of errorcode
Description: A General Error has occured during Control exchange
| L2.089 |
Level: C_INFO
Short Syntax: L2.089 Conn close in Function: errorcode
Long Syntax: L2.089 Connection being closed in Function due to error: errorcode
Description: A socket error has occured and the error is displayed 50 Network is down 51 Network is unreachable 52 Network dropped connection on reset* 53 Software caused connection abort 54 Connection reset by peer 55 No buffer space available 56 Socket is already connected 57 Socket is not connected 58 Can't send after socket shutdown 59 Too many references: can't splice 60 Connection timed out 61 Connection refused 62 Too many levels of symbolic links 63 File name too long 64 Host is down 65 No route to host 66 Directory not empty
| L2.090 |
Level: P-TRACE
Short Syntax: L2.090 Rcv PPTP Start-CC-Reply from host remote_hostname,result/error result/ error
Long Syntax: L2.090 Rcv PPTP Start-CC-Reply from host remote_hostname,result/error result/ error
Description: Received PPTP Start control connection reply from peer Result Codes: 1 - Successful channel establishment 2 - General error -- Error Code indicates the problem 3 - Command channel already exists; 4 - Requester is not authorized to establish a command channel 5 - The protocol version of the requester is not supported
| L2.091 |
Level: P-TRACE
Short Syntax: L2.091 Rcv PPTP OutCall-Reply from host remote_hostname,result/error result/ error
Long Syntax: L2.091 Rcv PPTP OutCall-Reply from host remote_hostname,result/error result/ error
Description: Received PPTP Outgoing Call Reply from peer Result Codes: 1 - Successful Connection 2 - General error -- Error Code indicates the problem 3 - No carrier 4 - Busy 5 - No dial tone 5 - Timeout 5 - Do not accept
| L2.092 |
Level: C-INFO
Short Syntax: L2.092 PPTP Tunnel id/ peer_id Send msg_type
Long Syntax: L2.092 PPTP Tunnel id/ peer_id Send msg_type
Description: PPTP tunnel sent a control message
| L2.093 |
Level: C-INFO
Short Syntax: L2.093 PPTP Session id/ peer_id Send msg_type
Long Syntax: L2.093 PPTP Session id/ peer_id Send msg_type
Description: PPTP session sent a control message
| L2.094 |
Level: P-TRACE
Short Syntax: L2.094 Rcv PPTP InCall-Reply from host remote_hostname,result/error result/ error
Long Syntax: L2.094 Rcv PPTP InCall-Reply from host remote_hostname,result/error result/ error
Description: Received PPTP Incoming Call Reply from peer Result Codes: 1 - Successful Connection 2 - General error -- Error Code indicates the problem 3 - Do Not Accept Call
| L2.095 |
Level: C_TRACE
Short Syntax: L2.095 L2F Call Opened- Type,net= net
Long Syntax: L2.095 L2F Call Opened- Type,net= net
Description: L2F Call FSM reached the OPENED state.
| L2.096 |
Level: P_TRACE
Short Syntax: L2.096 SEND client type, cid= cid tid= peer-cid
Long Syntax: L2.096 SEND client type, cid= cid tid= peer-cid
Description: Send the indicated client control message.
| L2.097 |
Level: P_TRACE
Short Syntax: L2.097 RCV protocol/ L2F_proto:F= flags,L= length,Tid= tunnelid,Cid= callid,NS= ns,O= offset
Long Syntax: L2.097 RCV protocol/ L2F_proto:F= flags,L= length,Tid= tunnelid,Cid= callid,NS= ns,O= offset
Description: Layer-2-Tunneling component received a tunneled packet. It is important to note that some of the displayed fields may NOT have been rcvd - use the "flags" mask to find which ones were rcvd.
| L2.098 |
Level: P_TRACE
Short Syntax: L2.098 SND protocol/ L2F_proto:F= flags,L= length,Tid= tunnelid,Cid= callid,NS= ns,O= offset
Long Syntax: L2.098 SND protocol/ L2F_proto:F= flags,L= length,Tid= tunnelid,Cid= callid,NS= ns,O= offset
Description: Layer-2-Tunneling component sending a tunneled packet. It is important to note that some of the displayed fields may NOT have been sent - use the "flags" mask to find which ones were sent.
| L2.099 |
Level: UE-ERROR
Short Syntax: L2.099 Multi L2 Tunnel - discard nt netnum
Long Syntax: L2.099 Multiple L2 tunnel - discard network netnum
Description: We do not support Layer-2-tunnels that get tunneled in another layer-2-tunnel.
Cause: Packet being passed to L2 has already been encapsulated with L2 tunnel.
Action: Reconfigure L2 or routing protocols to ensure that traffic is not caught in tunneling recursion.
| L2.100 |
Level: UE-ERROR
Short Syntax: L2.100 Process type L2F_CLOSE code= code
Long Syntax: L2.100 Process type L2F_CLOSE code= code
Description: received L2F_CLOSE from peer with a bitmask error code: 0x00000001 Authentication failed 0x00000002 Out of resources 0x00000004 Administrative intervention 0x00000008 User quota exceeded 0x00000010 Protocol error 0x00000020 Unknown user 0x00000040 Incorrect password 0x00000080 PPP configuration incompatible 0x00000100 Wrong multilink PPP destination 0xFF000001 No calls up on tunnel
| L2.101 |
Level: UI_ERROR
Short Syntax: L2.101 Err: no remote hostname on Out/Both nt net
Long Syntax: L2.101 Error: Outbound/Both net net without remote hostname
Description: L2 Net is configured as connection-direction outbound or both and is not configured with a remote hostname.
Action: Reconfigure L2 net as inbound or configure remote hostname.
| L2.102 |
Level: UE-ERROR
Short Syntax: L2.102 L2 packet(s) lost in transit tid= tid cid= cid new nr= nr
Long Syntax: L2.102 L2 packet(s) lost in transit tid= tid cid= cid new nr= nr
Description: Packet lost in transit - this can be a normal condition for lossy networks.